Sealey EH30001 Manuale Utente Scaricare il pdf (Pagina 2)

2. INTRODUCTION

3. SPECIFICATION

4. ASSEMBLY

Electric fan heater for industrial applications. Features three

heat settings and adjustable thermostat control with fan only

option. Auto cooling system to prevent unit from overheating

during use. A totally dry heat with no condensation, no gas,

no fumes and no smell. Ideal for workshops, garages etc.

Supplied with three phase chassis mounted plug (extension lead

required).

Model No: ............... . . . . . .EH30001

IP Class: ................ . . . . . . . . . IPX4

Max. Power:.............. . . . . . . .30000W

Supply: ................. . . . . . .415V-63A

Heat Settings: ............ . 15000/30000W

Dimensions (WxDxH (mm)): 645 x 565 x 860

g.1

g.2

g.3

4.3. ASSEMBLY OF THE HANDLE. (Ref. fig.3)

4.3.1. Slide a plain washer over each of the four M5 x 50mm bolts

supplied.

4.3.2. Lay the 'U' shaped handle frame onto the front face of the leg

frames and align the two holes at each end of the handle frame

with the two holes in each leg frame. Insert two bolts at each

joint as indicated in fig.3.

4.3.3. Whilst continuing to support the handle frame slide a plain

washer (P) followed by a split washer (T) onto the end of each

protruding bolt and retain them with a nut (S). Tighten all four

nuts with an 8mm spanner.

4.1. ASSEMBLY OF THE LEGS. (Ref. fig.1)

4.1.1. On either side of the heater body there are two threaded inserts

(B) for mounting the 'V' shaped leg frames (A). Note that the

axle hole at the shorter end of the 'V' frames should be

orientated towards the back of the heater.

4.1.2. Take two M8 x 40mm bolts (D) and slide a plain washer (C) onto

each one. Insert a bolt through each of the mounting holes on

the leg frame and slide a split washer (E) over each protruding

bolt. Align the bolts with the two threaded inserts (B) on the

heater body and screw them down securely.

4.1.3. Mount the other 'V' frame to the other side of the heater body in

the same way.

4.2. ASSEMBLY OF THE WHEELS. (Ref. fig.2)

4.2.1. Take the axle rod (F) and insert it through the holes in the 'V'

frames so that the threaded rod ends protrude equally either

side. Retain the axle rod in this position by inserting split pins

(G) through the holes situated just on the inside of each leg

frame.

4.2.2. Slide a plain washer (H) over each end of the axle rod, followed

by a wheel (J) followed by anther plain washer (H).

4.2.3. Screw a nyloc nut (L) onto each end of the axle by hand until it

begins to bite. Hold one nut steady with a 19mm spanner and

progressively tighten each nut until it bottoms out on the thread.

Original Language Version

1.2.4. COMMON SENSE PRECAUTIONS

 DO NOT operate the heater when you are tired or under the

influence of alcohol, drugs or intoxicating medication.

 DO NOT stand on the heater.

 DO NOT use the heater with wet hands or when there is water

on the power cord.

 Ensure that the heater is correctly turned off when not in use

and store in a safe, dry, childproof location.

 DO NOT use the heater for anything other than its intended

purpose. It is designed to provide heat in enclosed areas larger

than 4m³, such as workshops and other industrial areas. It is

not suitable for drying clothes or laundry.

IMPORTANT!

This unit is designed to raise the ambient temperature of an

entire room, the temperature of the air coming out of the front

of the heater will be warmer than the general temperature of the

room, but there may not be a signicant increase owing to the

large volume of air passing over the element. For the same

reason, the element is hot during operation, but does not

glow. The room temperature depends on room size, insulation

and the ambient temperature, which will increase as the room

gets warmer.

EH30001 Issue: 4(L) - 05/05/14

1 2 3

Commenti su questo manuale

Nessun commento

Sealey EH30001 Manuale Utente Pagina 2

Commenti su questo manuale

Prodotti e manuali riguardandi Radiatori Sealey EH30001