Sealey WPB50A Manuale Utente Scaricare il pdf (Pagina 2)

2. INTRODUCTION & SPECIFICATIONS

3. ASSEMBLY

4. OPERATION

Manufactured from corrosion resistant materials with a stainless steel motor case and noryl base cover.

Ideal for pumping water straight from a water butt directly onto your garden. Supplied with a two piece

aluminium swan neck extension pipe, adjustable ow control feature and snap on connector.

SPECIFICATION:

Model No: ............................................................ WPB50A

Cut-out: ..............................................................Automatic

Outlet O/D:...............................................................19mm

Maximum Output:..................................................50ltr(13gal)/min

Maximum Head:...........................................................10mtr

Minimum Water Depth: .....................................................50mm

Maximum Particle Size: .................................................... 0.5mm

Motor Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350W

Supply:...................................................................230V

fig.1 fig.2

3.1. DO NOT connect to the mains supply until the pump is immersed in the water butt.

3.2. Screw the extension into the swan neck, then screw the assembly onto the outlet connector. (g.1)

3.3. Clip the oat switch ex into the grip on the back of the pump unit (g.2) allowing the oat switch to rise and fall freely.

3.4. The pump cut-off point may be altered by clipping the oat switch ex to the grip tted on the extension (g.3), allowing the oat switch

to operate at a higher water level relative to the pump.

4.1. Place the pump unit in the water butt.

4.2. The pump must be installed and used in an upright position.

4.3. If silt is present on the bottom of the butt, place the pump on a brick so as to lift the base of the pump clear. This will protect the pump

from ingesting debris.

4.4. Connect hose pipe to the swan neck using a suitable female snap connector.

4.5. Connect the pump to the mains power supply; provided sufcient water is present to activate the oat switch, the pump will now run.

4.6. The output volume can be controlled by means of the ow control tted to the snap connector. Maximum ow is achieved with the

handle of the valve in line with the pipe. Flow is stopped with the handle at 90° to the pipe.

4.7. The oat switch is provided to protect the motor from dry running and consequent overheating; it is not intended as an on/off switch.

4.8. If the water ow is controlled by a cut-off device tted to the hose end, be aware that stopping the water ow will not stop the pump. No

damage will accrue if the ow is stopped for short periods, but avoid prolonged running in this condition.

4.9. The pump is not continuously rated: DO NOT run for more than 30minutes continuously, and allow 10minutes cooling at the end of this

time.

5. MAINTENANCE

 WARNING! With the exceptions listed below, all pump, float and electrical cable service maintenance and repair must only be

undertaken by an authorised service agent. Failure to observe this rule may be dangerous and will invalidate the warranty.

 WARNING! Ensure the pump is disconnected from the mains power supply before attempting any service or maintenance.

5.1. Keep all parts of the pump clean. Rinse, drain and allow to dry before storing the pump.

5.2. Regularly check the inlet filter in the base of the pump to ensure that there are no blockages. To access the filter, undo the filter

housing catch (fig.1) and remove the filter housing. Remove the circular foam filter element and wash in warm water. Replace the filter

and refit the housing onto the pump inlet.

DO NOT dismantle any other part of the unit.

Original Language Version

WPB50A Issue: 1 - 20/11/13

fig.3

1 2 3

Commenti su questo manuale

Nessun commento

Sealey WPB50A Manuale Utente Pagina 2

Commenti su questo manuale

Prodotti e manuali riguardandi Pompe Sealey WPB50A