INSTRUCTIONS FOR:
RACKING UNIT WITH 5 SHELVES
(150KG CAPACITY PER LEVEL)
MODEL No: AP6150GS
1. SAFETY
1.1 GENERAL SAFETY
WARNING! Ensure Health & Safety, and local authority
regulations are adhered to when assembling and using this
rack.
Locate rack in a suitable area where it will not be an
obstruction.
Keep the general area clean, uncluttered and ensure there is
adequate lighting.
WARNING! Erect rack on a level and solid surface such
as concrete.
Keep children and unauthorised persons away from the
storage area.
DO NOT use the rack for any purpose other than that for
which it is are designed.
DO NOT site the rack out of doors.
DO NOT get the rack wet or use in damp or wet locations
or areas where there is condensation.
DO NOT clean the shelf supports with any solvents which
may damage the surface.
Ensure that the rack is properly assembled before
loading them with heavy items.
Maximum load for each shelf is 150kg.
Where possible the rack should be fixed to the wall with
suitable fixings
Place heavier items on the lower shelves.
Heavier items should be evenly distributed across the shelves.
3. CONTENTS
2. INTRODUCTION
Carefully unpack the product and check the contents against the
list below. Should any items be missing or damaged make
immediate contact with your Sealey dealer.
Part Description No. Off
LEG ANGLE SECTIONS 8
LEG ANGLE JOINERS 8
PLASTIC FLOOR PROTECTORS 8
SHELF SUPPORT, LONG 10
SHELF SUPPORT, SHORT 10
MDF SHELF 5
FASTENER KIT (Nuts & bolts for joining side by side sections) 4
4. ASSEMBLY
4.1 Assemble the frame using a soft faced hammer or mallet as
shown in Fig.1. If only a hard faced hammer is available
hammer onto a piece of wood to avoid damaging the paint
surface. Always hammer gently as close as possible to the
uprights. Make sure that the shelf support tabs are in line with
the leg angle slots. If the tabs and slots are not lining up do not
Fig.1
4.3 See Fig.2. Decide on the height of the second shelf. Fit another
2 short shelf supports at the desired height then fit 2 long shelf
supports at the same height.
Fig.2
use force as this may damage the tabs. If the tabs are out of line
bend them slightly to line up with the slots.
4.2 See Fig.1. Decide on the position/height of the bottom shelf.
Make an end frame by fitting 1 short shelf support between 2 leg
angle sections. Make a second end frame ensuring that the shelf
support is at the same height as the first end frame. Join the two
end frames together using 2 long shelf supports fixed at the
same height as the short shelf supports.
Galvanised steel frame with five MDF shelves. 150kg capacity
per level giving a maximum capacity of 750kg per rack. No nuts
and bolts means no tools required to assemble. Clips together in
minutes. Two piece uprights allow use as a single bay rack, or
split in two separate shelf systems or workstations.
Height: 1805mm Width: 810mm Depth: 310mm
AP6150GS Issue No:2 (L) 21/10/14
Original Language Version
© Jack Sealey Limited
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
(4 pagine)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale